X300 OBDStar DP Plus Full Immobilizer Device - C Package FREE SHIPPING - SAUDI ARABIA BRANCH

Product Description
OBDSTAR X300 DP Plus C Package Full Configuration covers all functions of OBDSTAR X300 DP Key Master and supports more functions such as ECU
programming, Throttle programming, Airbag reset, Injector code+Suspension matching+Gear learning+CVT learning+DPF+ECU cloning+Adapter(P001
programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)

NOTE:

• Please check the supported car list of vehicle functions before you buy this device. If you are not sure whether the function or vehicle is supported, please feel free to inquiry us online
•  X300 DP Plus supports English only
• It doesn't support the following car models: DAIHATSU/ PROTON/ MAHINDRA/ MARUTI/ TATA/ HOLDEN/ LADA/ PERODUA/ IRAN.
• Please register first after receiving the product.
• X300 DP PLUS Registration and Upgrade Guide
  
  Differences Among OBDSTAR X300 DP Plus C Package (Full Version), A Package, and B Package:
  

X300 DP Plus C Full Configuration Diagnostic Function:

• Diagnose the electronic control system of prevailing vehicle models covering Asian, European, American, and Chinese. Diagnosis functions include: Read DTCS, Clear DTCS, Read data stream, Special functions etc.
• Classify special functions: ABS, EEPROM Adapter, Battery match, CVT learning, EPB, Gear learning, Immobilizer, TPMS (low tire) reset, Cluster calibrate, ECU programming, steering angle reset.
• Specially designed for Android platform with clear and user-friendly interface.
   
  X300 DP Plus C Full Configuration Software Advantages:
  1: ECU Clone
  ECU Clone means ECU duplication.
  The device copies all the data from the original vehicle ECU and then writes all data copied into ECU with the same hardware to realize the same ECU function with the original vehicle.
  2.Clone directly when replacing a new or a used ECU!
  Without online matching in the 4S store or removal of ECU bonding wire for reading and writing! Directly write without dismantling OBD!    
   3.Three features for ECU Clone:  
  A. Free of 4S online: break monopoly from 4S, benefiting automobile maintenance industry
  B. Simplified operation procedures: realize foolproof operation
  C. Non-dismantling with zero risks: read and write data without dismantling ECU

Switch activation function:
 (Today many instruments or audio of vehicles activate secondary power supply to go into power-on status by relevant module CAN communication on the vehicle,
but sometimes an instrument or an audio is separated from the vehicle CAN BUS network, causing startup failure when it needs to be repaired by an auto technician.
This function can simulate CAN communication to activate the secondary power supply, so the instrument or the audio enters into power-on status. In this way,
it not only can test and verify the instrument or the audio but also save an enormous cost for an auto technician to purchase a large number of startup platforms
of various vehicles and wiring harnesses!)

Add “Help” functions:
1. Contain built-in testable vehicle models, upgrade announcements, features, help notes and wiring diagrams, etc.
2. Car list: directly get it on the device
3. Upgrade Announcement: all details are available on the device
4. Customers can look up the features or uniquely support functions on the device
5. Help notes: built-in help notes for each model or function
8. Wiring diagrams: built-in ECU wiring diagrams, more intuitionistic and convenient
 
OBDSTAR X300 DP Plus C Full Configuration Hardware Advantages:
 1. Built-in VCI box, communication more stable
2. 8-inch touchscreen, more intuitionistic
3. Can be charged directly via OBD interface
4. Practical and high-end gift box
5. Industrial design with silicone case
6. Back bracket design: Can prop on the steering wheel or stand on the table, easier to operate
7. With simulated key 1 applies to the vehicle with 94/D4 type of smart key.
8. 3 in 1 P001 programmer: combined with EEPROM adapter + RFID adapter+ Key Renew adapter
9. Add the clip of reading SOP 8PIN EEPROM
10. Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)
11.Maintenance Database
12.Remote Assistant
13.One Key Upgrade
 
How to use OBDSTAR X300 DP Plus Induction Coil?
 1. Functional Overview: Induction Coil is used to detecting the key induction coil failure of the vehicle.

OBDSTAR X300 DP Plus A+B+C Full Configuration Technical Parameters

Other Configuration:
 
A Package: Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)
 
OBDSTAR X300 DP Plus vs. OBDSTAR X300 DP 

Picture	Obdstar X300  DP Plus	Obdstar X300  DP
Hardware & Design	Better	Good
Screen size and industrial design	√	×
Back holder	√	×
Work separately without VCI	√	×
Charged by OBDII	√	×
4 Toyota emulators	√	×
P001 programmer	√	×
Wiring harness for new functions, such as ECU cloning and switch activation	√
Software/Update
Immobilizer	√	√
Mileage	√	√
EEPROM	√	√
ECU Clone	√	×
Switch activation function	√	×
"Help" function - covers built-in support car list, upgrade announcement, help  notes and wiring diagrams	√	×
No need to pay for a software update for FREE during the valid time (one year)	√	×

Register directly on a tablet

Please connect to the network after receiving the device, enter the settings to register first.