Which vehicles does the MCKB005 adapter cover?

It is made for Toyota smart key remotes from 2018 to 2022 that use NXP NCF29xx series chips. Check that your key PCB matches the outline printed on the 05-FT02-V3.0 board before use.

Do I need to solder anything?

No. The board uses spring-loaded gold-plated pogo pins. You clamp the key PCB in position and contact is made automatically, so the customer's key stays undamaged.

What do the labels VCC, MSDA, WAKE, GND and MSCL mean?

They are the power and communication lines broken out on the adapter. VCC and GND supply power, MSDA and MSCL carry the data, and WAKE is used to wake the chip so it will respond.

Is a key programming tool included?

No. The MCKB005 is a hardware adapter only. You will need your own compatible key programmer and its software to run the key adding procedure.

NXP Smart Key Adapter P/N: MCKB005 For Toyota 2018 2022

CONDITION	new
Weight	0.1 kg

CONDITION	new

Weight	0.1 kg

Brand	Model	Year (From–To)
Toyota	----	2018–2022

NXP Smart Key Adapter P/N: MCKB005 For Toyota 2018-2022

The MCKB005 Universal NXP Key Programmer Adapter is a solder-free interface board built for Toyota smart key remotes. Rather than soldering flying leads onto delicate test points, you seat the key PCB into the 05-FT02-V3.0 fixture, close the two adjustable clamps, and the spring-loaded pogo pins make contact automatically. It is designed for locksmiths and automotive key shops handling Toyota key adding work daily who need a fast, repeatable and damage-free connection.

The adapter supports all NCF29xx series chip remotes, covering the Toyota proximity smart keys used across the 2018 to 2022 model years. The board carries a printed key outline for correct alignment, a dedicated WAKE contact point, and all required lines broken out on two labelled pin header rows — VCC, MSDA, WAKE, GND and MSCL — plus a multi-pin connector socket for ribbon cable hookup.

Key Features

Fits all NCF29xx chip remotes – one adapter covers the Toyota NXP smart key range for these years.
Zero soldering – gold-plated pogo pins contact the PCB test points directly, no heat or flux.
Twin clamp fixture – two adjustable screw clamps hold the key board flat and correctly aligned.
Dual labelled pin headers – VCC, MSDA, WAKE, GND and MSCL broken out on two rows for flexible hookup.
Dedicated WAKE point – marked directly on the board for remotes that need a wake-up signal.
Printed key outline – the PCB footprint is silk-screened on the board so positioning is obvious.
Connector socket included – on-board multi-pin socket for use with a ribbon harness.
Stable and repeatable – even clamping pressure means fewer failed reads and fewer retries.
Workshop ready – supplied in a protective clear storage case, ideal for mobile jobs.

How To Use

Open the Toyota smart key shell and carefully remove the remote PCB.
Place the PCB into the 05-FT02-V3.0 fixture, matching it to the key outline printed on the board.
Swing both clamps over the board and tighten them so the pogo pins press firmly on the contact points.
Wire the labelled VCC, MSDA, GND and MSCL pins to the matching terminals on your programming device, or use the on-board connector socket.
If your tool calls for a wake-up signal, connect to the point marked WAKE on the board.
Run the key adding procedure and follow the on-screen prompts through to completion.
Loosen the clamps, lift out the PCB, and reassemble the key.

Package Includes

1 x MCKB005 NXP Smart Key Adapter (05-FT02-V3.0 board)

Note: This adapter is a hardware interface only. A compatible key programming device and the relevant software licence are required to carry out key adding operations.