Hulkprog ECU & EEPROM Programmer – Bench, Boot & JTAG ECU TCU Tool

HULKPROG Universal MCU & Memory Programmer for Automotive Electronics

HULKPROG is a professional universal programmer built for ECU and module repair, immobilizer work, and bench-level chip programming. One tool reads, writes, clones, and repairs microcontrollers (MCUs) and memory chips (EEPROM, Flash, and serial memories) from Atmel, NXP/Freescale, Renesas, STMicroelectronics, Infineon, Microchip, Texas Instruments, and many more.

Unlike programmers with a locked device list, HULKPROG is user-defined: you choose the target chip, the interface, and the workflow. Read a donor module, write a replacement, write a virgin file or recover a bricked chip- all from one bench tool.

Key Features

• Universal ZIF socket for DIL chips, no soldering needed
• ISP / ICSP header with colour-coded pins to program chips directly on the PCB
• UART interface for boot-mode and single-wire programming protocols
• Status LEDs (Power, Busy, UART, ISP) for real-time feedback
• USB Type-C, DB-25 and DC power inputs in a rugged, shielded housing
• Adapter-ready for SOIC, TSOP, QFP and BGA socket adapters
• 20,000+ supported chips and vehicle modules for 52 brands, with automatic software updates

Programming Functions

• Read / Dump of Flash, EEPROM and configuration areas
• Write / Program firmware and calibration data
• Verify, Erase (full or sector) and Blank Check
• Automatic chip ID detection and checksum validation
• Read and edit config/fuse bits and protection registers
• OTP (one-time-programmable) device support
• On-board ISP programming without removing the chip

Applications

• ECU & TCU: read and write P-Flash / D-Flash on PowerPC, TriCore and Renesas units
• Immobilizer, BCM & KVM: EEPROM read/write and virgin file writing
• Module cloning: copy a donor module to a matched replacement
• Instrument cluster repair: restore EEPROM after a dashboard swap
• Bricked chip recovery: rebuild damaged memory from a good dump
• Tuning: Flash access for calibration and remapping
• Mercedes-Benz 48V battery repair (W206 / W223, Infineon TC277TP) with ready-made data files

Supported Chip Families

• Atmel: AT24, AT93, AT90, AT91SAM (ARM7/ARM9/Cortex), AVR XMEGA, megaAVR, tinyAVR
• Infineon: XC166, XE16x, XC2000, TriCore
• NXP / Freescale: HC08, S08, S12 / S12X / S12Z, MPC55/56 PowerPC, MCF51 Coldfire, LPC, Kinetis
• Renesas: RH850, V850, RL78, RX, SH, H8, M16C / M32C, R8C, 78K0
• STMicroelectronics: STM32, STM8, ST7, SPC56, M24 / M25 / M93 / M95
• Microchip: PIC10/12/16/18/32, dsPIC33, 24 / 93 series, SST25
• Texas Instruments: MSP430, TMS320F, TMS570LS, CC25
• Others: Micron / Numonyx, Spansion, GigaDevice GD25, Fujitsu, Seiko, EON

Package Contents

• 1 × HULKPROG programmer main unit
• 1 × Carry case
• 1 × Programming adapter board
• 1 × DB-25 jumper wire harness
• 1 × USB cable
• Connection and power cable set
• 1 × Power adapter

Software

Free Windows software (Windows 7 / 10 / 11) with a full chip catalogue, vehicle modules, wiring diagrams, and automatic updates. The software works only with a genuine HULKPROG programmer, as all programming algorithms run inside the device.