Tango SLK-06 Sniffer for Toyota-H Immobilizer AKL Solution

SLK-06 Smart Key Emulator Description:

Tango key programmer adds SLK-06 emulator for Toyota H Immobilizer All Keys Lost, works with Tango key programmer. The function allows solving all keys lost (AKL) situations on Toyota vehicles equipped with 128bit H immobilization system (Page1 39,59,3A,5A) regardless of the market (EU/Asia/USA), by creating a master key on LKP-04, utilizing SLK-06, which further serves for diagnostic authorization for key addition, without need to replace or reset the immobilizer. During the process, car data is not altered in any way.

Scorpio-LK Emulator SLK-06 for Tango Key Programmer

• Supports Toyota-H Immobilizer All Keys Lost solution (all markets) SLK-06 sniffer for Toyota-H Immobilizer All keys lost solution
• True Image Generator for Toyota H-Keys (Page1 3A, 7A) on TRPWS21 transponder

Toyota H Immobilizer All Keys Lost solution (all markets)

System requirements:

Tango key programmer
SLK-06 Sniffer
LKP-04 transponder
Toyota maker
SLK-06 maker
Internet connection
Any metal key that fits and can turn on the ignition switch of the vehicle

SLK-06 is battery-powered:

Note:  that a battery is not included with an emulator and has to be obtained locally.

• Three standard types of battery are compatible with our emulators: CR1616, CR1620, CR1632.
• If the battery is removed all data from the emulator will be lost. When power is restored the default data will be loaded into the transponder memory. Thus the transponder can be cleaned to default state just by taking off the battery.
• We did not test how long the battery life in this application is because the main purpose of the SLK-6 is to get data in few minutes. The battery shouldn't drop much below 3V or the emulator won't save data
• SLK-06 is not programmed.
• Default state after the battery replacement.

Operation Procedure:

Due to the nature of the Toyota H immobilization system, a creative approach is needed in order to solve all key lost situations, particularly for EU/Asia regions vehicles. The solution currently implemented in Tango can be summarized in three main steps, which are described below:

1. Obtaining data (Sniffing) Calculation (Calculate Data)
2. Master Key Creation (Write Transponder)
3. Obtaining data (Sniffing)

Disconnect battery from the car (1-3min)
Reconnect car battery
Insert the battery in SLK-06 (LED will blink few times, then go off)
Hold SLK-06 next to the ignition lock (as if it is a key)
Insert blank key blade (without any transponder) into the ignition and switch ON
If steps from 1 to 5 are performed correctly the LED of SLK-06 will start to Hold it in position until the LED stops blinking and turn solid red. At this point part of data gathering is complete.

Please note: Don't remove the battery from the SLK-06 emulator!
Turn ignition switch OFF and remove the key from
Perform again steps from 4 to 7 After this data gathering is complete.
When steps 1 to 8 are complete you can verify if data collection was performed successfully in Tango main software by using Autodetect:

SLK-06 is not programmed.
Default state after the battery replacement.

• Take note that during Autodetect Tango will turn OFF the SLK-06 LED, but this is not a problem, collected data remains.
  

Calculation (Calculate Data)

Connect Tango and start exe
Select region Asia, then Toyota->Utility->SLK06 Sniffer
Insert SLK-06 in Tango coil
Press Run Online Calculation (this step requires Internet connection)
You will receive a message that our servers have received your request and will start calculating the data.

The process can take from 6 minutes up to several hours (depends on several factors and servers' load).
Once servers have received the data SLK-06 is no longer needed, you can remove its battery.
Tango doesn't need to remain open, you can close the software, disconnect Tango, or continue using it for some other work. If Tango remains opened and there is an internet connection it will check once per minute for the status of the calculation request.

5. You can check the status of your request by pressing Check Calculation Status

6. When the calculation is complete you will be prompted to save a file.

• This step is optional and just allows proceeding with Master Key Creation at a later point, or in case you want to run another calculation right away. Our servers store the data of the last queued calculation indefinitely.
• The previous calculation is erased when a new calculation request is submitted.
• If you place a new request, while a previous is still being calculated, you will receive a message informing you that this action will cancel the current calculation, with the option to continue or cancel.

Master Key Creation (Write Transponder)

Once the Calculation process is complete, place a blank LKP-04 in the Tango coil
Press Write from Online Service

FAQ and Remarks

Q: Sniffer (SLK-06) doesn't blink?
A: Not inserted or low battery / Not placed correctly or next to ignition switch / Low or not connected vehicle battery or some other hardware issue with the vehicle. The sniffer itself can be tested in Tango. Place battery, start Tango, and press Autodetect.

Q: During Obtaining data LED on SLK-06 blinks, but then it doesn't turn solid?
A: Data obtaining failure. At present moment roughly 50% of all vehicles equipped with H immobilizer ever produced can be done using our system. Unfortunately, they can't be categorized by vehicle model/year/region or even part number.

Q: Error: Calculation error. Please make a new sniffing and try to calculate again
A: Blank or no SLK-06 placed in Tango / Obtaining data steps were not performed.

Q: Error: Detected zero captured frame. Expected at least two frames.
A: During Obtaining data steps 1 to 8 were not performed.

Q: Error: Detected one captured frame. Expected at least two frames.
A: During Obtaining data step 8 was not performed.

Q: I have a vehicle with an H IMMO system, key Page1 20.
A: At present moment P1 20 is not support, only the main types P1 39,59,3A,5A.